Angel juicer AG 10,000 Mini Commercial Juice Extractor:

Name : Angel Juice Extractor MINI
Model : Angel juicer AG10,000
Extracting Method : Twin Gear Triturating
RPM : 60 rpm
Motor : Electric Motor (watt), 10 HP
Weight & Dimension : 88 Lbs, 31.5� L x 11� W x 19� H
Capacity : Approximately 50 pounds Vegetables/Fruits per hour

Use: For Juice Bar, Restaurant, hospitals, clinics that treat their patients with juice and natural therapies, small farm, hotel, retreat centers, and other commercial use.

It is manufactured and optimized specifically for the food that is mainly would be juicing. You would need to tell us about the specific food you intend to use it for for example wheat grass, angelica etc. Then you would pay us by a wire transfer to our bank in South Korea. We will try our best to complete it as soon as possible (usually 1 to 4 weeks depends on how busy we are with the juicer orders for home). After completion, we test it juicing the food you pre-specified and weigh the pulp before and after. We make any necessary adjustments for optimal outcome. At this stage we may videotape the testing and email them to you for your final approval. Finally, we notify you that your juicer is ready to ship).

There are no parts to order with the Angel Juicer AG 10,000 mini commercial juice extractor. The only part you can order is another filter (a special order that you would need to email us) for the same food or another food. We are often asked if the Angel juicer AG10,000 mini can be used to juice all food. Yes, it can be used to juice all food, but the outcome may not be as optimal as the particular food it is designed for or food similar to it. The Angel juicer AG 10,000 can be used continuously unlike Angel juicers for home use that must be stopped and the filter cleaned once a container or two are full.

Angel juicer AG 10,000 mini is our most ordered commercial juicer.

Shipping about US$750 to US$1000. Please, allow 25 to 40 days after payment for shipping.

Please, Click here to view the Cord Types (You must specify the cord type you are interested in)

General guidemlines

Before operating the machine
Do not operate the machine with wet hands
Do not use the machine at in a place with excessive moisture
Unplug the Juice extractor from the electrical outlet when not in use, assembling, disassembling, cleaning, and removing food or other contents from the juicer (feeding chute)
Avoid contact with moving parts while the machine is in operation
Carefully read the instruction manual before operating

Operating Instruction
Plug the power cord into a grounded electrical outlet
Push the power switch up to run the motor (do not let the twin gears idle more than 15 seconds)
If the motor stops from a feed jam/overloading, push the power switch down (reverse position) for 3 to 5 seconds.
Place the power switch at the middle to stop the motor

How to disassemble & Clean the machine
Let the machine run for about one minute to get rid of excess feed/juice
Push the power switch down
Unplug the Juice extractor from the electrical outlet before disassembling and cleaning
Remove the housing cover
Unscrew the butterfly nuts on both sides and release the latches
Remove the screen housing (in case the screen housing does not release easily, turn the power switch ON/OFF one or twice then it will be released smoothly)
Remove the twin gears
Clean the screen housing with the cleaning brush under running water (do the same with the twin gears)
Dry with clean towel and then air dry the parts

How to Assemble the Gears
First, Insert the Driving Gear through the Driving Gear Shaft. Please Note! Slowly slide the driving gear through the driving gear shaft, but do not push the gear fully into the slot at this time. Right before the gear is set into the end of the slot, wiggle and/or turn the gear and so it is securely aligned with the gear shaft. Then, push the gear fully into the slot. Make sure the gears are fully seated.
Second, Insert the Free Wheel Gear through the Sub-Shaft.
Always make sure the gears are fully seated before operating. If you forcefully push the gear all the way into the slot without properly aligning them, the gear shaft can get damaged.
Slowly slide the screen housing over the twin gears and push it back.
Firmly tighten (do not over tighten) the butterfly nuts and place the screen housing cover